• CORROSION RESISTANCE OF AUSTENITIC NiMn-NODULAR CAST IRON IN NACL SOLUTION

  Publication Year: 2024

  VAŠKO, A. ZATKALÍKOVÁ, V. UHRÍČIK, M. KAŇA, V.

• CYCLIC LOW-THERMAL AGING OF DISSIMILAR AUSTENITIC STEEL WELDS USED IN NUCLEAR POWER PLANTS

  Publication Year: 2024

  MIKMEKOVÁ, Š. AMBROŽ, O. MRŇA, L. HRÁČEK, J. ŠEBESTOVÁ, H.

• DETERMINATION OF DYNAMIC PROPERTIES OF 3D PRINTED G3SI1 STEEL

  Publication Year: 2024

  SVOBODA, P. JOPEK, M. SVOBODA, O. HARANT, M.

• Determining the Dynamic Properties of Spruce Wood Using the Taylor Anvil Test

  Publication Year: 2024

  JOPEK, M. PIPÍŠKA, T. RÉH, R. KRIŠŤÁK, Ľ. KRÁL, P. RÁHEĽ, J. ŘÍDKÝ, R.

• Development of a test specimen carrier for the Taylor anvil test using 3D additive printing technology

  Publication Year: 2024

  JOPEK, M. MÜLLER, S. ŘIHÁČEK, J.

• Drive fast like a saw

  Publication Year: 2024

  PÍŠKA, M.

• Dynamic study of the compression strength of cuboid steel specimens cut of Hardox 450 sheet

  Publication Year: 2024

  JOPEK, M. SVOBODA, P. SOBCZYK, K. JANISZEWSKI, J. KRUSZKA L. MIKULSKI, E.

• High entropy alloys (FeCoNi) 0.75 Cr 0.25-x Cu x - thermal stability and physical properties

  Publication Year: 2024

  BROŽ, P. VŘEŠŤÁL, J. SOPOUŠEK, J. WEISS, K. BURŠÍK, J. BURŠÍKOVÁ, V. ZÁDĚRA, A. MÜLLER, P. ČUPERA, J. ROGL, G. PARZER, M. BAUER, E. MICHOR, H. ROGL.P.F.

• High-temperature lubricity of selected PVD coatings and methods of testing

  Publication Year: 2024

  PÍŠKA, M. HOLKOVÁ, K.

• INFLUENCE OF DEFORMATION TEMPERATURE AND STRAIN RATE ON THE MAXIMUM FLOW STRESS LEVEL OF THE 3D PRINTED AISI 316L STEEL

  Publication Year: 2024

  OPĚLA PETR, BENČ MAREK

• Influence of Imposed Strain on Weldability of Dievar Alloy

  Publication Year: 2024

  IZÁK, J. BENČ, M. KUNČICKÁ, L. OPĚLA, P. KOCICH, R.

• Influence of substitution of Cr by Cu on phase equilibria and microstructures in the Fe-Ni-Co-Cr high-entropy alloys

  Publication Year: 2024

  ZÁDĚRA, A. SOPOUŠEK, J. BURŠÍK, J. ČUPERA, J. BROŽ, P. JAN, V.

• Investigation of the tool wear progression in parting technology

  Publication Year: 2024

  DRBAL, M. KOLOMÝ, Š. SEDLÁK, J. ZOUHAR, J.

• Investigation of the Tool Wear Progression in Parting Technology

  Publication Year: 2024

  DRBAL, M. KOLOMÝ, Š. SEDLÁK, J. ZOUHAR, J. VÍTEK, J.

• Machinability of extruded H13 tool steel: Effect of cutting parameters on cutting forces, surface roughness, microstructure, and residual stresses

  Publication Year: 2024

  KOLOMÝ, Š. MALÝ, M. SEDLÁK, J. ZOUHAR, J. SLANÝ, M. HRABEC, P. KOUŘIL, K.

Showed 16–30 from 2152 results